GuidelinesRegulatory updates2026.11.11
PPWR Recyclability (Article 6) and Recycled Content (Article 7) — A Comparison Table of Questions, Evidence, Calculation and Application Dates
Some companies send a supplier document saying ‘recycled material was used’ as evidence of recyclability. Whether packaging can be recycled again after use (Article 6) and how much post-consumer plastic recycled content the packaging contains (Article 7) are different questions, each with its own evidence, calculation basis, application dates and exceptions. This guide compares the two requirements in one table and sets out the component assessment unit, two bundles of questions for suppliers and the misunderstandings that commonly mix them up.
Key takeaway — Article 6 asks ‘can the used packaging be recycled again’; Article 7 asks ‘how much post-consumer recycled content is in the plastic part of the packaging’. The evidence differs too. Recyclability needs an assessment of composition, joining, separation and the design criteria; content needs the origin of the material, the part concerned and the scope of calculation. Using one side's evidence to answer the other leaves a gap in the judgment even when documents exist.
This article is based on Regulation (EU) 2025/40 (PPWR) and Commission Notice C/2026/3084 (implementation guidance), as checked on 6 October 2026. The specification sheet for recording components is covered in packaging specification sheet and supplier document requests, and the document that holds the assessment results in the EU declaration of conformity guide.
Comparison table of the two requirements
| Aspect | Recyclability (Article 6) | Recycled content (Article 7) |
|---|---|---|
| What it asks | Is the packaging designed for material recycling after use, and can it be separately collected and sorted on disposal and recycled at scale? | Does the plastic part of the packaging contain at least the minimum percentage of recycled content recovered from post-consumer plastic waste? |
| Subject | All packaging placed on the market (Article 6(1)); exceptions in paragraph (11) | The plastic part of the packaging (Article 7(1)); exceptions in paragraphs (4) and (5) |
| Statutory criteria | Paragraph (2)(a) design for material recycling, (b) separate collection, sorting and recycling at scale. Paragraph (3) performance grades A, B and C (Annex II, Table 3) | Paragraph (1) 2030 percentages (contact-sensitive PET 30%, contact-sensitive other than PET 10%, single-use beverage bottles 30%, other 35%), paragraph (2) 2040 percentages |
| Calculation and assessment method | Paragraph (4) delegated act (design-for-recycling criteria, performance grades, assessment method, by 2028-01-01); paragraph (5) implementing act (recycling-at-scale assessment method, by 2030-01-01) | Average per manufacturing plant and year for each packaging type and format. Paragraph (8) implementing act (calculation and verification method and technical documentation format, by 2026-12-31) |
| Material conditions | Not applicable | Paragraph (3): collected within the EU or in a third country under equivalent separate collection standards and, where applicable, recycled in a facility subject to Directive 2010/75/EU or a facility meeting equivalent standards |
| Application date | Paragraph (1) principle under general application (2026-08-12). Paragraph (2)(a) from 2030-01-01 or 24 months after the delegated act enters into force, whichever is later. Point (b) from 2035-01-01 or 5 years after the implementing act enters into force, whichever is later | Paragraph (1) from 2030-01-01 or 3 years after the paragraph (8) implementing act enters into force, whichever is later. Paragraph (2) from 2040-01-01 |
| Exceptions | Paragraph (11): immediate packaging of medicinal products, contact-sensitive packaging of medical devices and in vitro diagnostic medical devices, outer packaging of medicinal products where needed to preserve quality, contact-sensitive packaging of infant and special medical purpose food, packaging for the transport of dangerous goods, lightweight wood, cork, textile, rubber, ceramic, porcelain or wax sales packaging (paragraph (8) applies) | Paragraph (4): immediate packaging of medicinal products, contact-sensitive plastic packaging of medical devices and devices for research and investigational use only, contact-sensitive plastic packaging of in vitro diagnostic medical devices, outer packaging of medicinal products, compostable plastic packaging, packaging for the transport of dangerous goods, contact-sensitive plastic packaging of infant and special medical purpose food, packaging of supplies for manufacturing medicinal products. Paragraph (5): food-contact packaging where recycled content poses a threat to human health, plastic parts below 5% of the total weight of the packaging unit |
| Evidence | Composition, joining and separation structure; assessment against the design criteria; the qualitative description under Annex VII point 2(e) | Origin of the material, the plastic part concerned, the basis of the plant and year average, technical documentation under the paragraph (8) implementing act |
Section 7 of the guidance explains that the two exceptions in Article 7(5) apply directly without a separate approval by the Commission or national authorities, but that the manufacturer must demonstrate fulfilment of the exception conditions with documented evidence in the technical documentation. It also explains that the polymer used must be specified for each plastic part making up 5% or more of the total weight of the packaging unit.
Recyclability is looked at by component
Article 6(9) provides that where a packaging unit has integrated components, they are all included in the assessment; integrated components that may become separated by mechanical stress during transport or sorting are assessed separately; and separate components are assessed individually. All components must be compatible with collection, sorting and recycling processes proven in an operational environment and must not hinder the recyclability of the main body of the packaging. This is why the name ‘PET bottle’ alone cannot settle the recyclability of the complete packaging.
Article 6(10) provides that from 1 January 2030 innovative packaging may benefit from an exception of up to 5 years from the end of the year of placing on the market, subject to notification to the competent authority before placing on the market and inclusion of the technical details and a timeline for reaching recycling at scale. It does not apply to ordinary packaging.
Recycled content asks about input material
Article 7(3) requires recycled content to be recovered from post-consumer plastic waste collected within the EU under national rules implementing this Regulation or the relevant directives, or collected in a third country under equivalent separate collection standards, and, where applicable, recycled in a facility within the EU subject to Directive 2010/75/EU or in a third-country facility with equivalent emission standards. The trade name ‘recycled material’ alone does not reveal these conditions. The origin of the material, the part of the packaging concerned, and the content and scope of calculation the data describe must be confirmed.
The weight table for a single bottle does not complete the statutory calculation of content. The calculation is based on the average per manufacturing plant and year for each packaging type and format, and the specific calculation and verification method and the technical documentation format are set by the Article 7(8) implementing act. This article does not write as if it had confirmed the adoption status of that implementing act.
Two bundles of questions for suppliers
| Bundle | Questions | Documents to receive |
|---|---|---|
| Recyclability | Material of each component and the multilayer, coating and adhesive structure · integrated or separate component · the conditions under which it separates in consumer use or sorting · the design criteria applied and the assessment evidence | Composition specification, explanation of separation conditions, assessment data |
| Recycled content | Origin of the recycled material (post-consumer waste or not, collection region and standards) · location and applicable standards of the recycling facility · the plastic part concerned and the percentage · the scope of the plant and year average calculation | Material evidence, calculation basis, applicable part numbers |
Even once both sets of documents are in hand, each must be checked against the applicable requirement, and the word ‘eco-friendly’ does not stand in for the judgment. The recycled content label under Article 12(4) is voluntary according to Section 13 of the guidance, but where it is used it must follow the implementing act specifications and the calculation method under Article 7(8).
Fictional example: a recycled-content bottle with a composite label
This is a fictional example for illustration. Suppose recycled material was used for the plastic container of an electronics accessory, but the structure and separation conditions of the label wrapped around the body were not checked. Even with a content document, the recyclability question about the complete packaging remains. Conversely, packaging that has been reviewed for recyclability has not thereby met the content requirement in Article 7. Splitting the document list into ‘composition and recyclability review’ and ‘material origin and content evidence’ and linking each to a packaging number reveals the missing documents. This example is not a compliance judgment on specific packaging.
Common misunderstandings
| Common explanation | What the legal text and guidance provide | What to check |
|---|---|---|
| All recycling requirements start in 2030 | The Article 6(1) principle applies from 2026-08-12. | Distinction between the current principle and the future design criteria |
| We used recycled material, so the packaging is recyclable | The two provisions ask different questions. | Component structure and separation conditions |
| The same percentage applies to all plastic | Article 7(1) sets different percentages by packaging type, with exceptions. | Contact-sensitive or not, main material |
| The content of one bottle completes the calculation | The plant and year average is the basis. | Scope of calculation |
| The 24 months of Article 6 also apply to Article 7 | Article 7(1) is 3 years after the implementing act enters into force. | The dates of each provision |
| Medical devices are automatically exempt from both | Article 6(11) and Article 7(4) differ in subject and conditions. | Exception review per provision |
Documents that speed up the review if prepared before inquiring
- Packaging composition and material specifications (per component)
- List of material and assessment documents received from suppliers
- Which packaging number and part number each document covers
Please mention PPWR packaging in your message when you use the PPWR packaging document review inquiry. We will set out which evidence connects to which of the two different questions. The scope and cost of the review are advised individually after we have confirmed the packaging configuration and the state of the documents.
Prepared and sources checked: 2026-10-06. Sources: Regulation (EU) 2025/40 Article 6(1) to (5) and (9) to (11), Article 7(1) to (5) and (8), Article 12(4), Annex VII point 2(e) · Commission Notice C/2026/3084 Section 6 (timing of recyclability application), Section 7 (recycled content exceptions), Section 13 (voluntary nature of content marking). The adoption status of the subsequent acts under Article 6(4) and (5) and Article 7(8) was not checked for this article. The comparison table, question table and fictional example are our own practical tools and do not replace a compliance judgment on individual packaging.
Frequently asked questions
- Q. From when does the requirement that packaging be recyclable apply?
- The principle in Article 6(1) that all packaging must be recyclable has no separate date, and according to Section 6 of the Commission guidance it applies from 12 August 2026. The design-for-recycling criteria in Article 6(2)(a) apply from 1 January 2030 or 24 months after the Article 6(4) delegated act enters into force, whichever is later, and the recycling-at-scale requirement in point (b) from 1 January 2035 or 5 years after the implementing act enters into force, whichever is later.
- Q. What percentage of recycled content is required for plastic?
- Article 7(1) provides that from 1 January 2030 or 3 years after the Article 7(8) implementing act enters into force, whichever is later, the following apply, calculated as an average per manufacturing plant and year for each packaging type and format: 30% for contact-sensitive PET packaging, 10% for contact-sensitive plastic packaging other than PET, 30% for single-use plastic beverage bottles and 35% for other plastic packaging. From 2040 the higher percentages in Article 7(2) apply. The exceptions and the conditions for post-consumer waste are set in the other paragraphs of the same article.
- Q. If recycled material was used, is the packaging recyclable?
- No. The use of recycled material is the Article 7 question about input material, while recyclability is the Article 6 question about whether the packaging can be collected, sorted and recycled after use. Labels, adhesives, coatings and the component structure affect recyclability, so the body material or the origin of the raw material alone cannot answer it.
- Q. Does the recyclability assessment have to go into the technical documentation right now?
- Article 6(9) requires compliance with the requirements in paragraphs (2) and (3) to be demonstrated in the Annex VII technical documentation, but Section 6 of the Commission guidance explains that until the Article 6(4) delegated act enters into force there is no need to carry out the conformity assessment under Article 38 and Annex VII for recyclability. The same section explains, however, that even before the delegated act, the requirements of the existing packaging waste directive and the relevant harmonized standards must be complied with.
